非官方整理 Unofficial notes 仅收录官方适配 Zero 的 Cap Official Zero-compatible Caps only

CardputerZero 的官方扩展模块

CardputerZero 机身带有顶部 EXT 2.54-14P Cap-Bus 和右侧 HY2.0-4P Grove 接口。目前官方 Cap 产品文档明确写明适配 CardputerZero 的,有 Cap LoRa-1262、Cap LoRa868 和 Cap CC1101。下面按官方文档介绍接口、安全和这三款模块的用途与用法。这不是官方商店或文档站点,也不列出未声明适配 Zero 的模块或未核实的售价。

Official expansion modules for CardputerZero

CardputerZero has a top EXT 2.54-14P Cap-Bus and a right-side HY2.0-4P Grove port. Official Cap product pages currently declare three modules as compatible with CardputerZero: Cap LoRa-1262, Cap LoRa868, and Cap CC1101. This section follows those official docs for the ports, safety notes, and how each Cap is used. This is not an official store or documentation site, and it does not list undeclared modules or unverified prices.

使用前先看这些 Read this first

官方文档写明:CardputerZero 搭配 Cap 系列产品时不支持热插拔。插入或移除 Cap 前,必须先将设备关机,否则可能导致工作异常。右侧 Grove 与顶部 EXT 的 5V 输出默认关闭,需在 Settings > ExtPort 中开启。Grove 5V 最大供电电流小于 500 mA。使用 LoRa 或 Sub-1 GHz 射频前,须遵守当地无线电管理法规,并合理配置频段、发射功率等参数。

Official docs state that Caps cannot be hot-swapped on CardputerZero. Power the device off before inserting or removing a Cap, or the hardware may misbehave. 5V output on the right-side Grove port and the top EXT port is off by default; enable it in Settings > ExtPort. Grove 5V is limited to less than 500 mA. Before using LoRa or Sub-1 GHz radio, follow local radio regulations and configure the band and transmit power accordingly.

本页没有收录什么

原版 ESP32 Cardputer 的配件、固件和教程,不能当作 CardputerZero 的官方扩展。只给出 Cardputer-Adv GPIO 对照、但未声明适配 Zero 的模块,也不列入本页。检索官方 Cap 产品文档时,目前明确写明适配 CardputerZero 的只有上述三款;若官方后续新增,以官方文档为准。本站不编造售价,也不整理未经官方声明的第三方兼容清单。

官方 Cap 文档常把 Arduino、UiFlow2 列为开发平台。这通常面向 MCU 或 Cardputer-Adv 等主机,不能据此推断 Arduino 或 UiFlow2 可直接运行在 CardputerZero 的 Linux 系统上。在 Zero 上使用这些模块,请以官方系统镜像、操作说明和预装应用为准。

与预装应用的对应关系

根据官方操作说明:GPS、LoRa 需连接 Cap LoRa-1262;NFC、SubG Chat 需连接 Cap CC1101。详细按键与用法写在对应模块页,系统镜像、烧录和全部预装软件见官方镜像与预装软件。

What is not listed here

Accessories, firmware, and tutorials for the original ESP32 Cardputer are not official CardputerZero expansions. Modules that only publish a Cardputer-Adv GPIO map, without a Zero compatibility statement, are also omitted. A search of official Cap product docs currently finds only the three Caps above declared for CardputerZero; if official docs add more later, those docs take precedence. This site does not invent prices or unofficial third-party compatibility lists.

Official Cap pages often list Arduino and UiFlow2 as development platforms. That typically refers to MCU or Cardputer-Adv hosts. It is not evidence that Arduino or UiFlow2 runs on CardputerZero’s Linux system. On Zero, follow the official system image, usage guide, and preinstalled apps.

How this maps to preinstalled apps

According to the official usage guide: GPS and LoRa require Cap LoRa-1262; NFC and SubG Chat require Cap CC1101. Key bindings and usage are on each Cap page. The official image, flashing steps, and the full preinstalled-software list are on the official image and software page.