未装天线不要上电。官方注意事项写明:请不要在没有安装天线的情况下连接或打开设备电源,否则硬件可能永久损坏。同时请遵守当地无线电管理法规,合理配置频段、发射功率和其他通信参数。搭配 CardputerZero 时不支持热插拔,插入或移除前先关机。模块提供两个与 Cardputer-Adv / Zero 匹配的螺丝孔,建议使用 M2 × 4 mm 螺丝;螺丝过长可能顶到内部 PCB 并造成损坏。

它是做什么的

LoRa 部分基于 SX1262,支持 868–923 MHz,最大发射功率 +22 dBm,接收灵敏度在 LoRa 低速率模式下低至 -147 dBm,支持 FSK / GFSK / MSK / GMSK / LoRa 调制,默认外置 RP-SMA 天线并带屏蔽罩。GPS 部分为 ATGM336H-6N(AT6668),内置陶瓷天线,UART 默认 115200 bps 8N1,可接收 GPS、QZSS、BD2、BD3、GALILEO、GLONASS 等系统。包装内容为模块本体和一根 LoRa 胶棒天线。

主要规格

下列数值均来自官方规格表,不是本站测算。

Do not power it without an antenna. Official notes say not to connect or power the device without an antenna, or the hardware may be permanently damaged. Follow local radio regulations and configure the band, transmit power, and other parameters accordingly. The Cap cannot be hot-swapped on CardputerZero; power off first. The module has two screw holes matching Cardputer-Adv / Zero; official docs recommend M2 × 4 mm screws. A screw that is too long can hit the internal PCB and cause damage.

What it does

The LoRa section is based on the SX1262, covering 868–923 MHz, with a maximum transmit power of +22 dBm and receive sensitivity down to -147 dBm in low-rate LoRa mode. It supports FSK / GFSK / MSK / GMSK / LoRa, uses an external RP-SMA antenna by default, and includes a shield. The GNSS section is ATGM336H-6N (AT6668) with a built-in ceramic antenna, UART at 115200 bps 8N1 by default, and support for GPS, QZSS, BD2, BD3, GALILEO, and GLONASS. The package includes the module and one LoRa rubber antenna.

Key specifications

The figures below come from the official specification table, not from measurements on this site.

LoRa 模组LoRa moduleSX1262
LoRa 频段LoRa band868 ~ 923 MHz
发射功率Transmit power+22 dBm
接收灵敏度Receive sensitivity-147 dBm(LoRa 低速率模式)
可编程比特率Programmable bit rateLoRa:最高 62.5 kbps;FSK:最高 300 kbps
LoRa 天线LoRa antenna108 × 9.3 mm,RP-SMA(内螺内孔),3 dBi
GPS 模组GPS moduleATGM336H-6N@AT6668
GPS 接口GPS interfaceUART,默认 115200 bps@8N1
定位精度 / 更新率Accuracy / update rate<1.5 m (CEP50);最大 10 Hz
尺寸 / 重量Size / weight84.0 × 24.0 × 15.2 mm;22.1 g(不含天线)

在 Zero 上怎么用预装应用

根据官方操作说明:

  • GPS:连接 Cap LoRa-1262 后打开应用,查看定位状态、经纬度、海拔等信息。用 Z / C 在 Position 和 Details 之间切换,用 F / X 滚动详情。
  • LoRa:连接 Cap LoRa-1262 后打开应用。进入发送页面并输入消息,按 ENTER 发送,按 ESC 取消。接收设备可在应用内查看消息。

插入模块前先关机,装好天线后再上电,并在需要时于 Settings > ExtPort 开启 5V。

管脚映射(按官方原表分列)

下面第一张是官方模块侧 Cap-Bus 信号表。第二组表在官方文档中标题为 Cardputer-Adv,其中的 G40、G39、G13、G15 等编号不能当作 CardputerZero 的 GPIO。Zero 主机侧编号见机身扩展接口。本站不自行合并这两套表。

官方还说明:LoRa 模组初始化时,需将 PI4IOE5V6408 的 P0 设为高电平,以打开射频天线开关(SX_ANT_SW)。模块另带 HY2.0-4P PORT.A(GND / 5V / SDA / SCL)。

Using the preinstalled apps on Zero

According to the official usage guide:

  • GPS: attach Cap LoRa-1262, then open the app to see fix status, latitude, longitude, altitude, and related data. Use Z / C to switch between Position and Details, and F / X to scroll details.
  • LoRa: attach Cap LoRa-1262, then open the app. Open the send page, type a message, press ENTER to send or ESC to cancel. A receiving device can view the message in the app.

Power off before attaching the Cap, fit the antenna before applying power, and enable 5V in Settings > ExtPort when needed.

Pin mapping (official tables, kept separate)

The first table is the official module-side Cap-Bus signal map. The following tables are titled Cardputer-Adv in the official docs; numbers such as G40, G39, G13, and G15 must not be treated as CardputerZero GPIO. Host-side Zero numbering is on the body ports page. This site does not merge the two maps.

Official docs also note that LoRa initialization must set P0 of the PI4IOE5V6408 high to enable the RF antenna switch (SX_ANT_SW). The module also exposes a HY2.0-4P PORT.A (GND / 5V / SDA / SCL).

Cap-Bus · Cap LoRa-1262

PINLEFTRIGHTPIN
GPS_TX114LoRa_NSS
GPS_RX213LoRa_MISO
SCL312LoRa_MOSI
SDA411LoRa_SCK
5V_OUT510LoRa_BUSY
GND69LoRa_IRQ
5V_IN78LoRa_RST

官方文档中的 Cardputer-Adv 对照(仅 Adv,不是 Zero GPIO)

Cardputer-Adv map from the official docs (Adv only — not Zero GPIO)

Cardputer-AdvG3G4G6G40G14G39G5
Cap LoRa-1262 (LoRa)RSTIRQBUSYSCKMOSIMISONSS
Cardputer-AdvG13G15
Cap LoRa-1262 (GPS)GPS-RXGPS-TX
Cardputer-AdvG8G9
Cap LoRa-1262 (PI4IOE5V6408)SDASCL
Cap LoRa-1262 (HY2.0-4P)SDASCL

关于 Arduino 与 UiFlow2

官方产品页将 Arduino、UiFlow2 列为开发平台。这通常面向 MCU 或 Cardputer-Adv 等主机,不能据此认为 Arduino 或 UiFlow2 可直接运行在 CardputerZero 的 Linux 系统上。在 Zero 上请以官方镜像、操作说明和预装 GPS / LoRa 应用为准。

About Arduino and UiFlow2

The official product page lists Arduino and UiFlow2 as development platforms. That typically refers to MCU or Cardputer-Adv hosts, and is not evidence that Arduino or UiFlow2 runs on CardputerZero’s Linux system. On Zero, follow the official image, usage guide, and the preinstalled GPS / LoRa apps.