它是做什么的
射频部分基于 TI CC1101,通过内置双 SP3T 开关和多频段匹配电路,把 315 MHz、433 MHz、868 MHz / 915 MHz 复用到一个 RP-SMA 接口,支持 2-FSK、4-FSK、GFSK、MSK、ASK、OOK 等调制,发射功率 +10 dBm。NFC 部分采用 ST25R3916,工作频率 13.56 MHz,读写器模式兼容 NFC-A/B(ISO14443A/B)、NFC-F(FeliCa)、NFC-V(ISO15693),卡模拟模式支持 NFC-A / NFC-F。模块通过 SPI 通信,并引出 HY2.0-4P Grove PORT.A 以便扩展传感器。
包装内容为模块本体,以及三根 RP-SMA 胶棒天线:315 MHz、433 MHz,以及一根同时适用于 868 MHz 与 915 MHz 的 868 MHz 天线。官方给出的通信距离是在 FSK、58 kbps 空中速率下测得:315 MHz 为 435 m,433 / 868 / 915 MHz 为 441 m。产品尺寸 84.0 × 24.0 × 19.7 mm,重量 14.9 g。
在 Zero 上怎么用预装应用
根据官方操作说明:
- NFC:连接 Cap CC1101 后打开应用,将标签靠近模块以读取信息。用
Z/C在扫描、标签详情和读卡器信息之间切换,用F/X滚动详情,按ENTER打开标签详情。 - SubG Chat:在参与聊天的设备上连接 Cap CC1101 并打开应用。用
Z/C切换消息和模块信息,用F/X滚动消息。按ENTER打开编辑器,也可直接输入字符开始编辑,再按ENTER发送。每条消息最多 56 个可打印 ASCII 字符。按ESC取消编辑。
插入模块前先关机,并在需要时于 Settings > ExtPort 开启 5V。
射频开关真值表
官方给出了 RF_SW0 / RF_SW1 与频段的对应关系。本站按原表收录,不补充文档未写出的接线细节。
What it does
The radio is based on the TI CC1101. Dual built-in SP3T switches and a multi-band matching network multiplex 315 MHz, 433 MHz, and 868 / 915 MHz onto one RP-SMA connector. Supported modulations include 2-FSK, 4-FSK, GFSK, MSK, ASK, and OOK, with a transmit power of +10 dBm. NFC uses the ST25R3916 at 13.56 MHz. Reader mode supports NFC-A/B (ISO14443A/B), NFC-F (FeliCa), and NFC-V (ISO15693); card-emulation mode supports NFC-A / NFC-F. The module communicates over SPI and exposes a HY2.0-4P Grove PORT.A for additional sensors.
The package includes the module and three RP-SMA rubber antennas: 315 MHz, 433 MHz, and an 868 MHz antenna that also covers 915 MHz. Official range figures are measured with FSK at 58 kbps: 435 m at 315 MHz, and 441 m at 433 / 868 / 915 MHz. The official size is 84.0 × 24.0 × 19.7 mm, and the weight is 14.9 g.
Using the preinstalled apps on Zero
According to the official usage guide:
- NFC: attach Cap CC1101, open the app, and hold a tag near the module to read it. Use
Z/Cto switch among scan, tag details, and reader information,F/Xto scroll details, andENTERto open tag details. - SubG Chat: attach Cap CC1101 on each participating device and open the app. Use
Z/Cto switch between messages and module information, andF/Xto scroll messages. PressENTERto open the editor, or start typing to edit, then pressENTERto send. Each message can contain at most 56 printable ASCII characters. PressESCto cancel editing.
Power off before attaching the Cap, and enable 5V in Settings > ExtPort when needed.
RF switch truth table
Official docs give the mapping from RF_SW0 / RF_SW1 to frequency bands. This page reproduces that table and does not add wiring details the docs omit.
| RF_SW0 | RF_SW1 | 频段 | Band |
|---|---|---|---|
| 0 | 0 | 315MHz | |
| 0 | 1 | 433MHz | |
| 1 | 1 | 868MHz/915MHz |
管脚映射(按官方原表分列)
第一张是模块侧 Cap-Bus 信号表(官方表中 7 号脚左侧无信号名)。随后的对照表标题为 Cardputer-Adv,其中的 G40、G39、G13、G15 等编号不能当作 Zero 的 GPIO。主机侧 Zero 编号见机身扩展接口。
Pin mapping (official tables, kept separate)
The first table is the module-side Cap-Bus signal map (the official table leaves the left side of pin 7 unlabeled). The following maps are titled Cardputer-Adv; numbers such as G40, G39, G13, and G15 must not be treated as Zero GPIO. Host-side Zero numbering is on the body ports page.
Cap-Bus · Cap CC1101
| PIN | LEFT | RIGHT | PIN |
|---|---|---|---|
| CC1101_G0 | 1 | 14 | CC1101_CS |
| CC1101_RF_SW0 | 2 | 13 | SPI_MISO |
| SCL | 3 | 12 | SPI_MOSI |
| SDA | 4 | 11 | SPI_SCLK |
| 5V_OUT | 5 | 10 | NFC_CS |
| GND | 6 | 9 | NFC_IRQ |
| 7 | 8 | POWER_EN |
官方文档中的 Cardputer-Adv 对照(仅 Adv,不是 Zero GPIO)
Cardputer-Adv map from the official docs (Adv only — not Zero GPIO)
| Cardputer-Adv | G5 | G13 | G15 | G40 | G14 | G39 |
|---|---|---|---|---|---|---|
| Cap CC1101 (CC1101) | CC1101_CS | CC1101_RF_SW0 | CC1101_G0 | SPI_SCLK | SPI_MOSI | SPI_MISO |
| Cardputer-Adv | G4 | G6 | G40 | G14 | G39 |
|---|---|---|---|---|---|
| Cap CC1101 (ST25R3916) | NFC_IRQ | NFC_CS | SPI_SCLK | SPI_MOSI | SPI_MISO |
HY2.0-4P · PORT.A
| HY2.0-4P | Black | Red | Yellow | White |
|---|---|---|---|---|
| PORT.A | GND | 5V | SDA | SCL |
关于 Arduino 与 UiFlow2
官方产品页将 Arduino、UiFlow2 列为开发平台。这通常面向 MCU 或 Cardputer-Adv 等主机,不能据此认为它们可直接运行在 CardputerZero 的 Linux 系统上。在 Zero 上请以官方镜像、操作说明和预装 NFC / SubG Chat 应用为准。
About Arduino and UiFlow2
The official product page lists Arduino and UiFlow2 as development platforms. That typically refers to MCU or Cardputer-Adv hosts, and is not evidence that they run on CardputerZero’s Linux system. On Zero, follow the official image, usage guide, and the preinstalled NFC / SubG Chat apps.