无线电法规仍然适用。官方操作说明要求:使用前确认并遵守当地无线电管理法规,合理配置 LoRa 工作频段、发射功率及其他通信参数。这款产品页没有重复 LoRa-1262 页上的“无天线不要上电”和螺丝规格,但不改变 CardputerZero 对所有 Cap 的要求:插入或移除前必须关机,不能热插拔。

它是做什么的

这是一款 LoRa 通信与 GNSS 定位扩展。LoRa 采用 Stamp LoRa-1262(SX1262),支持 868–923 MHz,最大发射功率 +20 dBm(官方 LoRa-1262 页为 +22 dBm),接收灵敏度在 LoRa 低速率模式下低至 -147 dBm,默认外置 RP-SMA 胶棒天线(3 dBi,108 × 9.3 mm)。GPS 采用 ATGM336H-6N(AT6668),内置陶瓷天线,UART 默认 115200 bps 8N1,支持 GPS / QZSS / BD2 / BD3 / GAL / GLO。包装内容为模块本体和一根 LoRa 胶棒天线。官方规格表给出的产品重量为 30.0 g,尺寸 84.0 × 24.0 × 15.2 mm。

与预装应用的关系

官方 CardputerZero 操作说明中,预装的 GPS、LoRa 应用写明需连接 Cap LoRa-1262。本站不把这两款预装应用写成也适用于 Cap LoRa868。若要在 Zero 的 Linux 系统上使用本模块的 LoRa 或定位功能,请以官方后续文档或你自行验证的软件为准,不要把原版 ESP32 Cardputer 的固件或界面当成 Zero 的用法。

主要规格

Radio regulations still apply. Official operating notes require you to follow local radio rules and to configure the LoRa band, transmit power, and other parameters accordingly. This product page does not repeat the “do not power without an antenna” warning or the screw size from the LoRa-1262 page, but the CardputerZero rule for every Cap still applies: power off before inserting or removing a module; no hot-swapping.

What it does

This is a LoRa and GNSS expansion. LoRa uses Stamp LoRa-1262 (SX1262), covering 868–923 MHz, with a maximum transmit power of +20 dBm (the official LoRa-1262 page lists +22 dBm) and receive sensitivity down to -147 dBm in low-rate LoRa mode. It ships with an external RP-SMA rubber antenna (3 dBi, 108 × 9.3 mm). GPS uses ATGM336H-6N (AT6668) with a built-in ceramic antenna, UART at 115200 bps 8N1 by default, and support for GPS / QZSS / BD2 / BD3 / GAL / GLO. The package includes the module and one LoRa rubber antenna. The official table lists a product weight of 30.0 g and a size of 84.0 × 24.0 × 15.2 mm.

Relation to preinstalled apps

In the official CardputerZero usage guide, the preinstalled GPS and LoRa apps name Cap LoRa-1262. This site does not claim those apps also support Cap LoRa868. If you use this module’s LoRa or GNSS functions on Zero’s Linux system, follow later official documentation or software you have verified yourself. Do not treat firmware or UI from the original ESP32 Cardputer as the Zero experience.

Key specifications

LoRa 模组LoRa moduleStamp LoRa-1262@SX1262
LoRa 频段LoRa band868 ~ 923 MHz
发射功率Transmit power+20 dBm
接收灵敏度Receive sensitivity-147 dBm(LoRa 低速率模式)
工作电流(官方测值)Operating current (official)GPS 工作 / LoRa 待机:DC 5V@29.24 mA;GPS 休眠 / LoRa 待机:DC 5V@3.16 mA;GPS 休眠 / LoRa 最大功率发送:DC 5V@129.72 mA;GPS 工作 / LoRa 最大功率发送:DC 5V@155.03 mA
GPS 模组 / 接口GPS module / interfaceATGM336H-6N@AT6668;UART 默认 115200 bps@8N1
尺寸 / 重量Size / weight84.0 × 24.0 × 15.2 mm;30.0 g

管脚映射(按官方原表分列)

第一张是模块侧 Cap-Bus 信号表,与 LoRa-1262 的官方 Cap-Bus 表一致。随后的对照表在官方文档中标题为 Cardputer-Adv,不能当作 Zero 的 GPIO 编号。这款产品页没有再列出 PI4IOE 天线开关或螺丝规格;主机侧 Zero 管脚见机身扩展接口。

Pin mapping (official tables, kept separate)

The first table is the module-side Cap-Bus signal map, which matches the official Cap-Bus table on LoRa-1262. The following maps are titled Cardputer-Adv in the official docs and must not be treated as Zero GPIO numbers. This product page does not repeat the PI4IOE antenna-switch note or screw size. Host-side Zero pins are on the body ports page.

Cap-Bus · Cap LoRa868

PINLEFTRIGHTPIN
GPS_TX114LoRa_NSS
GPS_RX213LoRa_MISO
SCL312LoRa_MOSI
SDA411LoRa_SCK
5V_OUT510LoRa_BUSY
GND69LoRa_IRQ
5V_IN78LoRa_RST

官方文档中的 Cardputer-Adv 对照(仅 Adv,不是 Zero GPIO)

Cardputer-Adv map from the official docs (Adv only — not Zero GPIO)

Cardputer-AdvG3G4G6G40G14G39G5
Cap LoRa868 (LoRa)RSTIRQBUSYSCKMOSIMISONSS
Cardputer-AdvG13G15
Cap LoRa868 (GPS)GPS-RXGPS-TX

关于 Arduino 与 UiFlow2

官方产品页将 Arduino、UiFlow2 列为开发平台。这通常面向 MCU 或 Cardputer-Adv 等主机,不能据此认为它们可直接运行在 CardputerZero 的 Linux 系统上。

About Arduino and UiFlow2

The official product page lists Arduino and UiFlow2 as development platforms. That typically refers to MCU or Cardputer-Adv hosts, and is not evidence that they run on CardputerZero’s Linux system.