它是做什么的
LoRa 部分基于 SX1262,支持 868–923 MHz,最大发射功率 +22 dBm,接收灵敏度在 LoRa 低速率模式下低至 -147 dBm,支持 FSK / GFSK / MSK / GMSK / LoRa 调制,默认外置 RP-SMA 天线并带屏蔽罩。GPS 部分为 ATGM336H-6N(AT6668),内置陶瓷天线,UART 默认 115200 bps 8N1,可接收 GPS、QZSS、BD2、BD3、GALILEO、GLONASS 等系统。包装内容为模块本体和一根 LoRa 胶棒天线。
主要规格
下列数值均来自官方规格表,不是本站测算。
What it does
The LoRa section is based on the SX1262, covering 868–923 MHz, with a maximum transmit power of +22 dBm and receive sensitivity down to -147 dBm in low-rate LoRa mode. It supports FSK / GFSK / MSK / GMSK / LoRa, uses an external RP-SMA antenna by default, and includes a shield. The GNSS section is ATGM336H-6N (AT6668) with a built-in ceramic antenna, UART at 115200 bps 8N1 by default, and support for GPS, QZSS, BD2, BD3, GALILEO, and GLONASS. The package includes the module and one LoRa rubber antenna.
Key specifications
The figures below come from the official specification table, not from measurements on this site.
| LoRa 模组 | LoRa module | SX1262 |
|---|---|---|
| LoRa 频段 | LoRa band | 868 ~ 923 MHz |
| 发射功率 | Transmit power | +22 dBm |
| 接收灵敏度 | Receive sensitivity | -147 dBm(LoRa 低速率模式) |
| 可编程比特率 | Programmable bit rate | LoRa:最高 62.5 kbps;FSK:最高 300 kbps |
| LoRa 天线 | LoRa antenna | 108 × 9.3 mm,RP-SMA(内螺内孔),3 dBi |
| GPS 模组 | GPS module | ATGM336H-6N@AT6668 |
| GPS 接口 | GPS interface | UART,默认 115200 bps@8N1 |
| 定位精度 / 更新率 | Accuracy / update rate | <1.5 m (CEP50);最大 10 Hz |
| 尺寸 / 重量 | Size / weight | 84.0 × 24.0 × 15.2 mm;22.1 g(不含天线) |
在 Zero 上怎么用预装应用
根据官方操作说明:
- GPS:连接 Cap LoRa-1262 后打开应用,查看定位状态、经纬度、海拔等信息。用
Z/C在 Position 和 Details 之间切换,用F/X滚动详情。 - LoRa:连接 Cap LoRa-1262 后打开应用。进入发送页面并输入消息,按
ENTER发送,按ESC取消。接收设备可在应用内查看消息。
插入模块前先关机,装好天线后再上电,并在需要时于 Settings > ExtPort 开启 5V。
管脚映射(按官方原表分列)
下面第一张是官方模块侧 Cap-Bus 信号表。第二组表在官方文档中标题为 Cardputer-Adv,其中的 G40、G39、G13、G15 等编号不能当作 CardputerZero 的 GPIO。Zero 主机侧编号见机身扩展接口。本站不自行合并这两套表。
官方还说明:LoRa 模组初始化时,需将 PI4IOE5V6408 的 P0 设为高电平,以打开射频天线开关(SX_ANT_SW)。模块另带 HY2.0-4P PORT.A(GND / 5V / SDA / SCL)。
Using the preinstalled apps on Zero
According to the official usage guide:
- GPS: attach Cap LoRa-1262, then open the app to see fix status, latitude, longitude, altitude, and related data. Use
Z/Cto switch between Position and Details, andF/Xto scroll details. - LoRa: attach Cap LoRa-1262, then open the app. Open the send page, type a message, press
ENTERto send orESCto cancel. A receiving device can view the message in the app.
Power off before attaching the Cap, fit the antenna before applying power, and enable 5V in Settings > ExtPort when needed.
Pin mapping (official tables, kept separate)
The first table is the official module-side Cap-Bus signal map. The following tables are titled Cardputer-Adv in the official docs; numbers such as G40, G39, G13, and G15 must not be treated as CardputerZero GPIO. Host-side Zero numbering is on the body ports page. This site does not merge the two maps.
Official docs also note that LoRa initialization must set P0 of the PI4IOE5V6408 high to enable the RF antenna switch (SX_ANT_SW). The module also exposes a HY2.0-4P PORT.A (GND / 5V / SDA / SCL).
Cap-Bus · Cap LoRa-1262
| PIN | LEFT | RIGHT | PIN |
|---|---|---|---|
| GPS_TX | 1 | 14 | LoRa_NSS |
| GPS_RX | 2 | 13 | LoRa_MISO |
| SCL | 3 | 12 | LoRa_MOSI |
| SDA | 4 | 11 | LoRa_SCK |
| 5V_OUT | 5 | 10 | LoRa_BUSY |
| GND | 6 | 9 | LoRa_IRQ |
| 5V_IN | 7 | 8 | LoRa_RST |
官方文档中的 Cardputer-Adv 对照(仅 Adv,不是 Zero GPIO)
Cardputer-Adv map from the official docs (Adv only — not Zero GPIO)
| Cardputer-Adv | G3 | G4 | G6 | G40 | G14 | G39 | G5 |
|---|---|---|---|---|---|---|---|
| Cap LoRa-1262 (LoRa) | RST | IRQ | BUSY | SCK | MOSI | MISO | NSS |
| Cardputer-Adv | G13 | G15 |
|---|---|---|
| Cap LoRa-1262 (GPS) | GPS-RX | GPS-TX |
| Cardputer-Adv | G8 | G9 |
|---|---|---|
| Cap LoRa-1262 (PI4IOE5V6408) | SDA | SCL |
| Cap LoRa-1262 (HY2.0-4P) | SDA | SCL |
关于 Arduino 与 UiFlow2
官方产品页将 Arduino、UiFlow2 列为开发平台。这通常面向 MCU 或 Cardputer-Adv 等主机,不能据此认为 Arduino 或 UiFlow2 可直接运行在 CardputerZero 的 Linux 系统上。在 Zero 上请以官方镜像、操作说明和预装 GPS / LoRa 应用为准。
About Arduino and UiFlow2
The official product page lists Arduino and UiFlow2 as development platforms. That typically refers to MCU or Cardputer-Adv hosts, and is not evidence that Arduino or UiFlow2 runs on CardputerZero’s Linux system. On Zero, follow the official image, usage guide, and the preinstalled GPS / LoRa apps.