不能热插拔,并注意螺丝长度。官方写明:搭配 CardputerZero 时不支持热插拔,插入或移除前先关机。模块提供两个与 Cardputer-Adv / Zero 匹配的螺丝孔,建议使用 M2 × 4 mm 螺丝;螺丝过长可能顶到内部 PCB 并造成损坏。使用 Sub-1 GHz 射频时,请选择包装内对应频段的天线,并遵守当地无线电管理法规。官方本页没有像 LoRa-1262 那样单独写出“无天线不要上电”,但仍应按所连频段安装对应天线。

它是做什么的

射频部分基于 TI CC1101,通过内置双 SP3T 开关和多频段匹配电路,把 315 MHz、433 MHz、868 MHz / 915 MHz 复用到一个 RP-SMA 接口,支持 2-FSK、4-FSK、GFSK、MSK、ASK、OOK 等调制,发射功率 +10 dBm。NFC 部分采用 ST25R3916,工作频率 13.56 MHz,读写器模式兼容 NFC-A/B(ISO14443A/B)、NFC-F(FeliCa)、NFC-V(ISO15693),卡模拟模式支持 NFC-A / NFC-F。模块通过 SPI 通信,并引出 HY2.0-4P Grove PORT.A 以便扩展传感器。

包装内容为模块本体,以及三根 RP-SMA 胶棒天线:315 MHz、433 MHz,以及一根同时适用于 868 MHz 与 915 MHz 的 868 MHz 天线。官方给出的通信距离是在 FSK、58 kbps 空中速率下测得:315 MHz 为 435 m,433 / 868 / 915 MHz 为 441 m。产品尺寸 84.0 × 24.0 × 19.7 mm,重量 14.9 g。

在 Zero 上怎么用预装应用

根据官方操作说明:

  • NFC:连接 Cap CC1101 后打开应用,将标签靠近模块以读取信息。用 Z / C 在扫描、标签详情和读卡器信息之间切换,用 F / X 滚动详情,按 ENTER 打开标签详情。
  • SubG Chat:在参与聊天的设备上连接 Cap CC1101 并打开应用。用 Z / C 切换消息和模块信息,用 F / X 滚动消息。按 ENTER 打开编辑器,也可直接输入字符开始编辑,再按 ENTER 发送。每条消息最多 56 个可打印 ASCII 字符。按 ESC 取消编辑。

插入模块前先关机,并在需要时于 Settings > ExtPort 开启 5V。

射频开关真值表

官方给出了 RF_SW0 / RF_SW1 与频段的对应关系。本站按原表收录,不补充文档未写出的接线细节。

No hot-swapping, and watch screw length. Official docs state that the Cap cannot be hot-swapped on CardputerZero; power off first. The module has two screw holes matching Cardputer-Adv / Zero; official docs recommend M2 × 4 mm screws. A screw that is too long can hit the internal PCB and cause damage. For Sub-1 GHz radio, fit the packaged antenna that matches the band, and follow local radio regulations. This official page does not repeat the LoRa-1262 “do not power without an antenna” wording, but the matching antenna for the selected band should still be installed.

What it does

The radio is based on the TI CC1101. Dual built-in SP3T switches and a multi-band matching network multiplex 315 MHz, 433 MHz, and 868 / 915 MHz onto one RP-SMA connector. Supported modulations include 2-FSK, 4-FSK, GFSK, MSK, ASK, and OOK, with a transmit power of +10 dBm. NFC uses the ST25R3916 at 13.56 MHz. Reader mode supports NFC-A/B (ISO14443A/B), NFC-F (FeliCa), and NFC-V (ISO15693); card-emulation mode supports NFC-A / NFC-F. The module communicates over SPI and exposes a HY2.0-4P Grove PORT.A for additional sensors.

The package includes the module and three RP-SMA rubber antennas: 315 MHz, 433 MHz, and an 868 MHz antenna that also covers 915 MHz. Official range figures are measured with FSK at 58 kbps: 435 m at 315 MHz, and 441 m at 433 / 868 / 915 MHz. The official size is 84.0 × 24.0 × 19.7 mm, and the weight is 14.9 g.

Using the preinstalled apps on Zero

According to the official usage guide:

  • NFC: attach Cap CC1101, open the app, and hold a tag near the module to read it. Use Z / C to switch among scan, tag details, and reader information, F / X to scroll details, and ENTER to open tag details.
  • SubG Chat: attach Cap CC1101 on each participating device and open the app. Use Z / C to switch between messages and module information, and F / X to scroll messages. Press ENTER to open the editor, or start typing to edit, then press ENTER to send. Each message can contain at most 56 printable ASCII characters. Press ESC to cancel editing.

Power off before attaching the Cap, and enable 5V in Settings > ExtPort when needed.

RF switch truth table

Official docs give the mapping from RF_SW0 / RF_SW1 to frequency bands. This page reproduces that table and does not add wiring details the docs omit.

RF_SW0RF_SW1频段Band
00315MHz
01433MHz
11868MHz/915MHz

管脚映射(按官方原表分列)

第一张是模块侧 Cap-Bus 信号表(官方表中 7 号脚左侧无信号名)。随后的对照表标题为 Cardputer-Adv,其中的 G40、G39、G13、G15 等编号不能当作 Zero 的 GPIO。主机侧 Zero 编号见机身扩展接口。

Pin mapping (official tables, kept separate)

The first table is the module-side Cap-Bus signal map (the official table leaves the left side of pin 7 unlabeled). The following maps are titled Cardputer-Adv; numbers such as G40, G39, G13, and G15 must not be treated as Zero GPIO. Host-side Zero numbering is on the body ports page.

Cap-Bus · Cap CC1101

PINLEFTRIGHTPIN
CC1101_G0114CC1101_CS
CC1101_RF_SW0213SPI_MISO
SCL312SPI_MOSI
SDA411SPI_SCLK
5V_OUT510NFC_CS
GND69NFC_IRQ
78POWER_EN

官方文档中的 Cardputer-Adv 对照(仅 Adv,不是 Zero GPIO)

Cardputer-Adv map from the official docs (Adv only — not Zero GPIO)

Cardputer-AdvG5G13G15G40G14G39
Cap CC1101 (CC1101)CC1101_CSCC1101_RF_SW0CC1101_G0SPI_SCLKSPI_MOSISPI_MISO
Cardputer-AdvG4G6G40G14G39
Cap CC1101 (ST25R3916)NFC_IRQNFC_CSSPI_SCLKSPI_MOSISPI_MISO

HY2.0-4P · PORT.A

HY2.0-4PBlackRedYellowWhite
PORT.AGND5VSDASCL

关于 Arduino 与 UiFlow2

官方产品页将 Arduino、UiFlow2 列为开发平台。这通常面向 MCU 或 Cardputer-Adv 等主机,不能据此认为它们可直接运行在 CardputerZero 的 Linux 系统上。在 Zero 上请以官方镜像、操作说明和预装 NFC / SubG Chat 应用为准。

About Arduino and UiFlow2

The official product page lists Arduino and UiFlow2 as development platforms. That typically refers to MCU or Cardputer-Adv hosts, and is not evidence that they run on CardputerZero’s Linux system. On Zero, follow the official image, usage guide, and the preinstalled NFC / SubG Chat apps.